Mat.No. 1.3243, DIN S6-5-2-5, AISI M35
Short Description:
Designation by Standards Mat. No. DIN EN AISI 1.3243 S6-5-2-5 HS6-5-2-5 M35 Chemical Composition (in weight %) C Si Mn Cr Mo Ni V W Others 0.91 max. 0.45 max. 0.40 4.15 - 1.90 6.30 - Co: 4.75 Description M35 is molybdenum high speed steel. Very high resistance to wear and to softening at elevated temperatures. High resistance of cutting edge and good toughness. Deep hardening response. High hot hardness. Applications Highly stressed drills, milling cutters, profile cutting to...
Product Detail
FAQ
Product Tags
Designation by Standards
| Mat. No. | DIN | EN | AISI |
| 1.3243 | S6-5-2-5 | HS6-5-2-5 | M35 |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.91 | max. 0.45 | max. 0.40 | 4.15 | - | 1.90 | 6.30 | - | Co: 4.75 |
Description
M35 is molybdenum high speed steel. Very high resistance to wear and to softening at elevated temperatures. High resistance of cutting edge and good toughness. Deep hardening response. High hot hardness.
Applications
Highly stressed drills, milling cutters, profile cutting tools, thread cutting drills and cold forming tools.
Physical properties (avarage values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 217
Density [g/cm3]: 8.1
Thermal conductivity [W/m.K]: 19.0
Electric resistivity [Ohm mm2/m]: 0.60
Specific heat capacity[J/g.K]: 0.46
Coefficient of Linear Thermal Expansion 10-6 oC-1
| 20-100oC | 20-200oC | 20-300oC | 20-400oC | 20-500oC | 20-600oC | 20-700oC |
| 9.7 | 10.5 | 11.0 | 11.4 | 11.5 | 12.0 | 12.5 |
Soft Annealing
Heat to 820-880oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 230-300.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to 650oC, holding for one hour at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Heat to 450-600oC, preheat to 850oC and then to 1050oC. Harden from a temperature of 1210-1250oC followed by oil, air quenching or warm bath 550oC. Hardness after quenching is 64-66 HRC.
Transformation temperatures: Ac1=824oC , Ac3=853oC.
Tempering
Tempering temperature: 3 x 1 hour at 540-570oC.
Tempering Temperature (oC) vs. Hardness (HRC)
| 200oC | 300oC | 400oC | 500oC | 525oC | 550oC | 575oC | 600oC | 650oC | 700oC |
| 63 | 61 | 62 | 64 | 64.5 | 65 | 64 | 63 | 55 | 46 |
Tempering Diagram
Click the image to enlarge the diagram.
Forging
Hot forming temperature: 1100-900oC.
Machinability
No data.
Corrosion Resistance
Not normally employed in applications requiring corrosion resistance.
Forms manufactured: Please see the Dimensional Sales Program.
FAQ Content
