Mat.No. 1.1213، DIN Cf53، ايسي 1055

Mat.No.  1.1213، DIN Cf53، ايسي 1055

وصف قصير:

  Designation by Standards   Mat. No. DIN EN AISI 1.1213 Cf53 - 1055   Chemical Composition (in weight %)   C Si Mn Cr Mo Ni V W Others 0.53 0.25 0.55 - - - - - -   Description Unalloyed structural carbon steel. Applications Steels for superficial hardening: Piston bolts, chain bolts, gear shafts, gear wheels, worms and camshafts. Physical properties (avarage values) at ambient temperature Modulus of elasticity [103 x N/mm2]: 210 Density [g/cm3]: 7.84 ...


  • FOB السعر: US $ 0.5 - 9999 / قطعة
  • مين. وردر الكمية: 100 قطعة / قطعة
  • إنتاج القدرة: 10000 قطعة / قطعة في الشهر
  • الميناء: شنتشن
  • شروط الدفع: L / C، D / A، D / P، T / T
  • تفاصيل المنتج

    التعليمات

    علامات المنتج

     

    تسمية المعايير

     

    حصيرة. لا. DIN EN ايسي
    1.1213 Cf53 - 1055

     

    التركيب الكيميائي (وزن٪)

     

    C سي مليون كر مو ني الخامس W الآخرين
    0.53 0.25 0.55 - - - - - -

     

    وصف Unalloyed structural carbon steel. تطبيقات Steels for superficial hardening: Piston bolts, chain bolts, gear shafts, gear wheels, worms and camshafts. الخصائص الفيزيائية (قيم أفاراجي) في درجة حرارة الجو المحيط Modulus of elasticity [103 س N / مم 2]: 210 Density [g/cm3]: 7.84 لينة التليين Heat to 650-700س C, cool slowly. This will produce a maximum Brinell hardness of 223. تطبيع Temperature: 830-860س C.تخفيف الاجهاد Stress relieving to remove machining stresses should be carried out by heating to 120-200س C, holding for one hour at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment. تصلب Harden from a temperature of 810-845س C followed by oil or water quenching. Hardness after quenching is 57-62 HRC. هدأ Tempering temperature: 550-660س C.خصائص الميكانيكية في تصلب + خفف من الحالة

     

    القطر (مم) 0.2٪ الإجهاد الإثبات (N / مم 2) قوة الشد (N / مم 2) استطالة (٪) اختزال (٪)
    ما يصل الى 16 510 740-880 12 25
    17-40 430 690-830 14 35
    41-100 400 640-780 15 40

     

    تزوير Hot forming temperature: 1050-850س C.التشغيل في الماكينات No data. تنصل The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other puposes. There is no representation that the recipient of this literature will receive updated editions as the become available.

  • السابق:
  • التالي:
  • التعليمات المحتوى

    إرسال رسالتك لنا:

    منتجات ذات صله